15188633222产品中心
联系我们
名称：保定巨盛模具制造有限公司
电话：13833064090
手机：15188633222
联系人：高经理
地址：河北省保定市清苑区阎庄乡中阎庄村
新闻动态
模具机械维护与保养
模具机械维护与保养
Mold machinery maintenance
1：模具长时间使用后必须磨刃口，研磨后刃口面必须进行退磁，不能带有磁性，否则易发生堵料。
1: After a long time of use, the cutting edge must be grinded, and demagnetization must be carried out on the edge surface after grinding. Otherwise, blocking is easy to occur.
2：弹簧等弹性零件在使用过程中弹簧最易损坏，通常出现断裂和变形现象。采取的办法就是更换，在更换过程中一定要注意弹簧的规格和型号，弹簧的规格和型号通过颜色、外径和长度三项来确认，只有在三项都相同的情况下才可以更换。
2: Spring and other elastic parts are easy to be damaged in the process of use, and usually appear fracture and deformation. The method adopted is to replace. In the process of replacement, pay attention to the specification and model of spring. The specification and model of spring are confirmed by color, outer diameter and length, and can only be replaced when the three items are the same.
3：模具使用过程中冲头易出现折断、弯曲和啃坏的现象，冲套一般都是啃坏的。冲头和冲套的损坏一般都用相同规格的零件进行更换。冲头的参数主要有工作部分尺寸、安装部分尺寸、长度尺寸等。
3: The punch is easy to break, bend and gnaw during the use of die, and the punching sleeve is generally gnawed. The damage of punch and punch sleeve is usually replaced with parts of the same specification. The parameters of punch mainly include working part size, installation part size, length dimension, etc.
4：紧固零件，检查紧固零件是否松动、损坏现象，采取的办法是找相同规格的零件进行更换。
4: Fasten the parts, check whether the fastening parts are loose or damaged. The method is to replace the parts with the same specifications.
5：压料零件如压料板、优力胶等，卸料零件检查井钢模具 隔离墩模具 隔离墩钢模具 流水槽模具 U型槽模具 螺杆启闭机 卷扬式启闭机 铜雕佛像如脱料板、气动顶料等。保养时检查各部位的配件关系及有无损坏，对损坏的部分进行修复，气动顶料检查有无漏气现象，并对具体的情况采取措施。如气管损坏进行更换。
5: Pressing parts such as pressure plate, Unisex, etc., unloading parts such as stripper, pneumatic jacking, etc. During maintenance, check the relationship between parts and whether there is any damage, repair the damaged part, check whether there is air leakage by pneumatic jacking, and take measures for the specific situation. If the air pipe is damaged, replace it
Mold machinery maintenance
1：模具长时间使用后必须磨刃口，研磨后刃口面必须进行退磁，不能带有磁性，否则易发生堵料。
1: After a long time of use, the cutting edge must be grinded, and demagnetization must be carried out on the edge surface after grinding. Otherwise, blocking is easy to occur.
2：弹簧等弹性零件在使用过程中弹簧最易损坏，通常出现断裂和变形现象。采取的办法就是更换，在更换过程中一定要注意弹簧的规格和型号，弹簧的规格和型号通过颜色、外径和长度三项来确认，只有在三项都相同的情况下才可以更换。
2: Spring and other elastic parts are easy to be damaged in the process of use, and usually appear fracture and deformation. The method adopted is to replace. In the process of replacement, pay attention to the specification and model of spring. The specification and model of spring are confirmed by color, outer diameter and length, and can only be replaced when the three items are the same.
3：模具使用过程中冲头易出现折断、弯曲和啃坏的现象，冲套一般都是啃坏的。冲头和冲套的损坏一般都用相同规格的零件进行更换。冲头的参数主要有工作部分尺寸、安装部分尺寸、长度尺寸等。
3: The punch is easy to break, bend and gnaw during the use of die, and the punching sleeve is generally gnawed. The damage of punch and punch sleeve is usually replaced with parts of the same specification. The parameters of punch mainly include working part size, installation part size, length dimension, etc.
4：紧固零件，检查紧固零件是否松动、损坏现象，采取的办法是找相同规格的零件进行更换。
4: Fasten the parts, check whether the fastening parts are loose or damaged. The method is to replace the parts with the same specifications.
5：压料零件如压料板、优力胶等，卸料零件检查井钢模具 隔离墩模具 隔离墩钢模具 流水槽模具 U型槽模具 螺杆启闭机 卷扬式启闭机 铜雕佛像如脱料板、气动顶料等。保养时检查各部位的配件关系及有无损坏，对损坏的部分进行修复，气动顶料检查有无漏气现象，并对具体的情况采取措施。如气管损坏进行更换。
5: Pressing parts such as pressure plate, Unisex, etc., unloading parts such as stripper, pneumatic jacking, etc. During maintenance, check the relationship between parts and whether there is any damage, repair the damaged part, check whether there is air leakage by pneumatic jacking, and take measures for the specific situation. If the air pipe is damaged, replace it
