15188633222产品中心
联系我们
名称：保定巨盛模具制造有限公司
电话：13833064090
手机：15188633222
联系人：高经理
地址：河北省保定市清苑区阎庄乡中阎庄村
新闻动态
模具之规格
(1).模具尺寸与锁紧螺丝
(1) . die size and locking screw
模板之尺寸应大于工作区域，并选择标准模板尺寸。模板锁紧螺丝之位置配置与模具种类及模板尺寸有关。其中单工程模具最常使用锁紧螺丝配置于四边角，最标准形式工作区域可广大使用。长形之模具及连续模具最常使用锁紧螺丝配置于四边角及中间位置。
The size of the formwork shall be larger than the working area, and the standard formwork size shall be selected. The position of the locking screw of the template is related to the type and size of the template. Among them, the single engineering mould is most often equipped with locking screws at four corners, and the most standard working area can be widely used. Locking screws are most often used for long and continuous molds at four corners and in the middle.
(2).模板之厚度
(2) . thickness of formwork
模板之厚度选择与模具之构造、冲压加工种类、冲压加工加工力、冲压加工精度等有绝对关系。依据理论计算决定模具之厚度是困难的，一般上系由经验求得，设计使用的模板厚度种类宜尽量少，配合模具高度及夹紧高度加以标准化以便利采购及库存管理。
The thickness of the die is absolutely related to the structure of the die, the type of stamping, the force of stamping and the precision of stamping. It is difficult to determine the thickness of the die according to the theoretical calculation. Generally, it is obtained by experience. The thickness of the die used in the design should be as few as possible, and the die height and clamping height should be standardized to facilitate procurement and inventory management.
(1) . die size and locking screw
模板之尺寸应大于工作区域，并选择标准模板尺寸。模板锁紧螺丝之位置配置与模具种类及模板尺寸有关。其中单工程模具最常使用锁紧螺丝配置于四边角，最标准形式工作区域可广大使用。长形之模具及连续模具最常使用锁紧螺丝配置于四边角及中间位置。
The size of the formwork shall be larger than the working area, and the standard formwork size shall be selected. The position of the locking screw of the template is related to the type and size of the template. Among them, the single engineering mould is most often equipped with locking screws at four corners, and the most standard working area can be widely used. Locking screws are most often used for long and continuous molds at four corners and in the middle.
(2).模板之厚度
(2) . thickness of formwork
模板之厚度选择与模具之构造、冲压加工种类、冲压加工加工力、冲压加工精度等有绝对关系。依据理论计算决定模具之厚度是困难的，一般上系由经验求得，设计使用的模板厚度种类宜尽量少，配合模具高度及夹紧高度加以标准化以便利采购及库存管理。
The thickness of the die is absolutely related to the structure of the die, the type of stamping, the force of stamping and the precision of stamping. It is difficult to determine the thickness of the die according to the theoretical calculation. Generally, it is obtained by experience. The thickness of the die used in the design should be as few as possible, and the die height and clamping height should be standardized to facilitate procurement and inventory management.
